Before we return to the schmuck
, there is going to be a small intermezzo.
In the future GIMP will lose its indexed mode. As I wrote last time
: creative work is RGB work. Ages ago I made a solutions model how GIMP could still support producing indexed images. This means doing the creative work in RGB, here shown at 200%:
When it is time to prepare an
indexed version, a projection screen
can be pulled over the image window that shows how the user‐controlled indexed set‑up works out, in this case a modest 16 colors:
The core of the solution model is that this projection is again a surface,
that can be worked on, to make the corrections that are specific to this indexed set‑up. The non‑destructive nature of GEGL
makes it possible to reapply these corrections after more creative development, or to adjust them at a later stage.
It is from the projection that an export to indexed file formats is performed.
a coin drops
Cut to the chase: it was while reading the GIMP review
on ars technica by Dave Girard, where he used ‘vinyl’
and ‘audio masters’
to describe CMYK and RGB. Suddenly I could see the parallels with the indexed situation.
going to press
Here is my solutions model for preparing artwork for the printing press in GIMP.
By now it should come as no surprise
that all creative work is going to be in RGB. This has also the benefit that at all
GIMP plugins work, without a chance of color shifting conversions. Here is a schematic representation of creative work on a jazz poster, built out of four layers:
, found at: polish jazz art in nyc
At any stage during the project, when there is a need to work towards the printing presses, a press projection
can be pulled over the image window that shows how the user‐controlled plate set‑up works out, in this case a five‐plate job:
The layer stack—used in the creative development—is not used in this view. Instead what matters is the user’s plate set‑up, which is displayed and controlled as a similar stack. Each plate is fully editable: painting, curves, gradients, (lots of) plugins, anything goes. This gives us the required full control
over the plates.
Note also that the colors in the press projection are already slightly different than that of the normal view, because the color profile of the printing press is taken into account.
it’s all a set‑up
Everything hinges on the particular set‑up of the press projection. This is where users freely set—as required
—the number of plates and what ink/paint/lacquer is used for each plate. Any color will be possible and we can support metallic paints and matt/glossy transparent varnishes, using a bit of animation on the projection.
The set‑up is also the place where the more tricky stuff is supported: overprint and trapping, rich blacks, combined ink limits: it is probably only the beginning of how advanced this has to get. I had not forgotten
CMYK + spot
In general the plate separation is calculated from the composite image that feeds into the press projection. However there will be full flexibility to map the content of any layer directly to any plate. For instance that light blue text in our example: it can be directly mapped from its text layer to the light blue plate, bypassing the composite.
Here is also the one and only time that CMYK will play a role in GIMP: as a small configuration file that is a default (OK, the
default) for the projection set‑up. Nothing more, nothing less.
Since the press projection can be freely pulled over the image window and then flipped up again, GIMP will be able to fully support the required creative workflow
. The mosaic below shows GIMP tracking in 16 steps real‐life work on either the creative concept or on the printing plates:
The non‑destructive nature of GEGL makes that whenever the press projection is pulled down, the updated artwork is re‑separated and all previously made plate optimisations are re‑applied on top. When the underlying artwork changes significantly, then every existing plate optimisation step can be validated by users and where needed adjusted.
The result is maximum creative flexibility and minimal rework of the plates over the life‐cycle of the file. Ah yeah, of course the whole press projection will be saved in the GIMP file. At the end, it is from the press projection that an export is performed to the file formats appropriate for shipping to the printers’.
what about CMYK files?
When a received CMYK file is to be used in new creative work, we already saw
that ‘it needs to be imported and converted to RGB.’
When further fine‐tuning for the printing press is the goal, then the solution is to shove the CMYK file straight into a press projection, as a static, pre-defined separation. Each plate is then still fully editable as outlined before.
That concludes my current take on ‘not quite
the CMYK’ issue: bringing artwork to printing presses. Actually at LGM
it turned out to be a hot topic in quite a few talks held by several projects. My contribution of squaring this circle fell neatly into place there.
Stay tuned for the last part of my LGM talk: a single‐window interface for GIMP.